UNS S42010 Enquiry | Print this page
- Category
- Type
- Steel grade
- Standard
- Country
- USE
- Grades
- Special Alloy
- » S42010
S41500
S41500
S41610
S41610
416P1usX(XM-6)
416P1usX(XM-6)
Type418(GreekAscollOy)
Type418(GreekAscollOy)
S41800
S41800 - UNS
- USA
- Martensitic special steel
Chemical composition % of the ladle analysis of grade S42010
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | Ni(％) | Mo(％) |
| 0.15-0.30 | 1 | 1 | Max 0.04 | Max 0.04 | 13.5-15.0 | 0.25-1.00 | 0.40-1.00 |
| Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
|---|---|---|---|---|---|---|
| 516 (≥) | 838 (≥) | 21 | 23 | 41 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 211 |
| Property | Density kg/dm3 |
Temperature T °C/F |
Specific heat J / kgK |
Thermal conductivity W/mK |
Electric resistance µΩ·cm |
Modulus of elasticity kN/mm2 |
Expansion rate |
|---|---|---|---|---|---|---|---|
| 166 (≥) | 499 (≥) | 44 | 11 | 13 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 231 | |
| Temp. °C/°F |
Creep strain limit (10000h) (Rp1,0) N/mm2 |
Creep rupture strength (10000h) (Rp1,0) N/mm2 |
|||||
| 544 | 623 | 232 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates / Sheets | Plates / Sheets | 0.08-200mm(T)*W*L | Forging, hot rolling and cold rolling | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Steel Bar | Round Bar, Flat Bar, Square Bar | Φ8-1200mm*L | Forging, hot rolling and cold rolling, Cast | Black, Rough Turning, Shot Blasting, |
| Coil / Strip | Steel Coil /Steel Strip | 0.03-16.0x1200mm | Cold-Rolled & Hot-Rolled | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Pipes / Tubes | Seamless Pipes/Tubes, Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion, Cold Drawn, Welded | Annealed, Solution and Aging, Q+T, ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| A 276 S42010 | Stainless Steel Bars and Shapes |
||
| A 314 S42010 | Stainless Steel Billets and Bars for Forging |
||
| A 493 S42010 | Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging |
||
| A 959 S42010 | Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Stainless Steels |
||
| F 899 S42010 | Standard Specification for Wrought Stainless Steels for Surgical Instruments |
||
| S42010 | Hardenable Chromium Stainless Steel |
||
| SA-276 S42010 | Specification for Stainless Steel Bars and Shapes |