UNS S41610 Enquiry | Print this page
- Category
- Type
- Steel grade
- Standard
- Country
- USE
- Grades
- Special Alloy
- » S41610
Type410Cb(XM-30)
S41040
S41040
S41050
S41050
CA6NM
CA6NM
S41500
S41500
S41610 - UNS
- USA
- Martensitic special steel
Chemical composition % of the ladle analysis of grade S41610
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | Mo(％) |
| 0.15 | 1 | 1.5-2.5 | Max 0.06 | Min 0.15 | 12.0-14.0 | 0.6 |
| Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
|---|---|---|---|---|---|---|
| 416 (≥) | 249 (≥) | 32 | 24 | 31 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 322 |
| Property | Density kg/dm3 |
Temperature T °C/F |
Specific heat J / kgK |
Thermal conductivity W/mK |
Electric resistance µΩ·cm |
Modulus of elasticity kN/mm2 |
Expansion rate |
|---|---|---|---|---|---|---|---|
| 885 (≥) | 698 (≥) | 12 | 23 | 21 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 421 | |
| Temp. °C/°F |
Creep strain limit (10000h) (Rp1,0) N/mm2 |
Creep rupture strength (10000h) (Rp1,0) N/mm2 |
|||||
| 438 | 642 | 382 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates / Sheets | Plates / Sheets | 0.08-200mm(T)*W*L | Forging, hot rolling and cold rolling | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Steel Bar | Round Bar, Flat Bar, Square Bar | Φ8-1200mm*L | Forging, hot rolling and cold rolling, Cast | Black, Rough Turning, Shot Blasting, |
| Coil / Strip | Steel Coil /Steel Strip | 0.03-16.0x1200mm | Cold-Rolled & Hot-Rolled | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Pipes / Tubes | Seamless Pipes/Tubes, Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion, Cold Drawn, Welded | Annealed, Solution and Aging, Q+T, ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| A 581 S41610 | Free-Machining Stainless Steel Wire and Wire Rods |
||
| A 582 S41610 | Standard Specification for Free-Machining Stainless Steel Bars |
||
| S41610 | Martensitic Chromium Free Machining Stainless Steel |
||
| A 581 S41610 | Free-Machining Stainless Steel Wire and Wire Rods |
||
| A 582 S41610 | Standard Specification for Free-Machining Stainless Steel Bars |
||
| S41610 | Martensitic Chromium Free Machining Stainless Steel |