AFNOR X3CrNiMoBN17-13-3 Enquiry | Print this page
- Category
- Type
- Steel grade
- Standard
- Country
- USE
- Grades
- Special Alloy
- » X3CrNiMoBN17-13-3
30CrNiMo8
34CrNiMo6
35B2
40CrMoV4-6
41NiCrMoV7-3-2
42CrMo5-6
C35E
NiCr20TiAI
NiCr15Fe7TiAI
X2CrNb18-9 - AFNOR
- France
- Fasteners with stainless steel and nickel alloy for high temperature and low temperature (NF-EN 10269(1999))
Chemical composition % of the ladle analysis of grade X3CrNiMoBN17-13-3
C(%) | Si(%) | Mn(%) | P(%) | S(%) | Cr(%) | Ni(%) | Mo(%) | N(%) | B(%) |
Max 0.04 | Max 0.75 | Max 2.00 | Max 0.035 | Max 0.015 | 16.0-18.0 | 12.0-14.0 | 2.00-3.00 | 0.10-0.18 | 0.0015-0.0050 |
Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
---|---|---|---|---|---|---|
978 (≥) | 116 (≥) | 43 | 23 | 21 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 412 |
Property | Density kg/dm3 |
Temperature T °C/F |
Specific heat J / kgK |
Thermal conductivity W/mK |
Electric resistance µΩ·cm |
Modulus of elasticity kN/mm2 |
Expansion rate |
---|---|---|---|---|---|---|---|
979 (≥) | 828 (≥) | 24 | 12 | 13 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 442 | |
Temp. °C/°F |
Creep strain limit (10000h) (Rp1,0) N/mm2 |
Creep rupture strength (10000h) (Rp1,0) N/mm2 |
|||||
397 | 977 | 518 |
Product type | Products | Dimension | Processes | Deliver Status |
---|---|---|---|---|
Plates / Sheets | Plates / Sheets | 0.08-200mm(T)*W*L | Forging, hot rolling and cold rolling | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
Steel Bar | Round Bar, Flat Bar, Square Bar | Φ8-1200mm*L | Forging, hot rolling and cold rolling, Cast | Black, Rough Turning, Shot Blasting, |
Coil / Strip | Steel Coil /Steel Strip | 0.03-16.0x1200mm | Cold-Rolled & Hot-Rolled | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
Pipes / Tubes | Seamless Pipes/Tubes, Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion, Cold Drawn, Welded | Annealed, Solution and Aging, Q+T, ACID-WASHED |
Grade | Standard | Country | Application |
---|---|---|---|
X2CrNiMo17-12-2 | DIN 1654-5 (1989) Cold heading and cold extruding steels; technical delivery conditions for stainless steels; Replaced by DIN EN 10263-5:2002 |
||
1.4404 | DIN 1654-5 (1989) Cold heading and cold extruding steels; technical delivery conditions for stainless steels; Replaced by DIN EN 10263-5:2002 |
||
X2CrNiMo17-13-2 | DIN 1654-5 (1989) Cold heading and cold extruding steels; technical delivery conditions for stainless steels; Replaced by DIN EN 10263-5:2002 |
||
X2CrNiMo17-12-2 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
||
1.4404 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
||
X2CrNiMo17-12-2 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
||
1.4404 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
||
X2CrNiMo17-12-2 | Stainless steels - Chemical composition |