ISO ISO X5CrNiMo17-12 Enquiry | Print this page
- Category
- Type
- Steel grade
- Standard
- Country
- USE
- Grades
- Special Alloy
- » ISO X5CrNiMo17-12
X3CrNiCu18 9 3E
ISO X2CrNi18-10
ISO X5CrNi18-9 Tube
ISO X7CrNi18-9
ISO X6CrNiNb18-11
ISO X7CrNiNb18-11
ISO X6CrNiTi18-10 Tube
ISO X7CrNiTi18-10 Tube
ISO X2CrNiMo17-12 Tube
ISO X2CrNiMo17-13 - ISO
- ISO
- ISO standard austenitic stainless steel pressure seamless steel tube
Chemical composition % of the ladle analysis of grade ISO X5CrNiMo17-12
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | Ni(％) | Mo(％) |
| Max 0.07 | Max 1.00 | Max 2.00 | Max 0.040 | Max 0.030 | 16.5-18.5 | 2.00-2.50 | 10.5-13.5 |
| Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
|---|---|---|---|---|---|---|
| 948 (≥) | 538 (≥) | 11 | 14 | 13 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 442 |
| Property | Density kg/dm3 |
Temperature T °C/F |
Specific heat J / kgK |
Thermal conductivity W/mK |
Electric resistance µΩ·cm |
Modulus of elasticity kN/mm2 |
Expansion rate |
|---|---|---|---|---|---|---|---|
| 725 (≥) | 866 (≥) | 22 | 34 | 43 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 343 | |
| Temp. °C/°F |
Creep strain limit (10000h) (Rp1,0) N/mm2 |
Creep rupture strength (10000h) (Rp1,0) N/mm2 |
|||||
| 591 | 679 | 268 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates / Sheets | Plates / Sheets | 0.08-200mm(T)*W*L | Forging, hot rolling and cold rolling | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Steel Bar | Round Bar, Flat Bar, Square Bar | Φ8-1200mm*L | Forging, hot rolling and cold rolling, Cast | Black, Rough Turning, Shot Blasting, |
| Coil / Strip | Steel Coil /Steel Strip | 0.03-16.0x1200mm | Cold-Rolled & Hot-Rolled | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Pipes / Tubes | Seamless Pipes/Tubes, Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion, Cold Drawn, Welded | Annealed, Solution and Aging, Q+T, ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| X5CrNiMo17-12-2 | DIN 1654-5 (1989) Cold heading and cold extruding steels; technical delivery conditions for stainless steels; Replaced by DIN EN 10263-5:2002 |
||
| 1.4401 | DIN 1654-5 (1989) Cold heading and cold extruding steels; technical delivery conditions for stainless steels; Replaced by DIN EN 10263-5:2002 |
||
| X5CrNiMo-18-10 | DIN 17224 (1982) Stainless steel wire and strip for springs; technical delivery conditions; Replaced by DIN EN 10151:2003; DIN EN 10270-3:2001 |
||
| X5CrNiMo17-12-2 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
||
| 1.4401 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
||
| X5CrNiMo17-12-2 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
||
| 1.4401 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel |
||
| X5CrNiMo17-12-2 | Stainless steels - Chemical composition |
||
| X5CrNiMo17-12-3 | Stainless steels - Chemical composition |
||
| X5CrNiMo17-12 2E | Steels for cold heading and cold extruding |
||
| X5CrNiMo17-12 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Longitudinally welded austenitic stainless steel tubes |
||
| X5CrNiMo17-12 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Longitudinally welded austenitic stainless steel tubes |