Location » Home » Grades > Special Alloy > 5ΧΗΜ

EN 5ΧΗΜ Enquiry | Print this page

Tags

Chemical composition % of the ladle analysis of grade 5ΧΗΜ

C(％) Si(％) Mn(％) P(％) S(％) Cr(％) Ni(％) Mo(％) V(%) W(%) Cu(%) Ti(%)
0.50-0.60 0.10-0.40 0.50-0.80 ≤0.030 ≤0.030 0.50-0.80 1.40-1.80 0.15-0.30 ≤0.15 ≤0.20 ≤0.30 ≤0.03
Mechanical properties of grade 5ΧΗΜ
Proof strength
Rp0.2 (MPa)		 Tensile strength
Rm (MPa)		 Impact energy
KV (J)		 Elongation at fracture
A (%)		 Reduction in cross section on fracture
Z (%)		 As-Heat-Treated Condition Brinell hardness (HBW)
214 (≥) 338 (≥) 14 34 12 Solution and Aging, Annealing, Ausaging, Q+T,etc 133
Physical properties of grade 5ΧΗΜ
Property Density
kg/dm3		 Temperature T
°C/F		 Specific heat
J / kgK		 Thermal conductivity
W/mK		 Electric resistance
µΩ·cm		 Modulus of elasticity
kN/mm2		 Expansion rate
228 (≥) 499 (≥) 21 14 23 Solution and Aging, Annealing, Ausaging, Q+T,etc 244
Temp.
°C/°F		 Creep strain limit
(10000h)
(Rp1,0) N/mm2		 Creep rupture strength
(10000h)
(Rp1,0) N/mm2
178 664 929
5ΧΗΜ Range of products
Product type Products Dimension Processes Deliver Status
Plates / Sheets Plates / Sheets 0.08-200mm(T)*W*L Forging, hot rolling and cold rolling Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting
Steel Bar Round Bar, Flat Bar, Square Bar Φ8-1200mm*L Forging, hot rolling and cold rolling, Cast Black, Rough Turning, Shot Blasting,
Coil / Strip Steel Coil /Steel Strip 0.03-16.0x1200mm Cold-Rolled & Hot-Rolled Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting
Pipes / Tubes Seamless Pipes/Tubes, Welded Pipes/Tubes OD:6-219mm x WT:0.5-20.0mm Hot extrusion, Cold Drawn, Welded Annealed, Solution and Aging, Q+T, ACID-WASHED
Cross Reference Table(Equivalent Grade)
Grade Standard Country Application
1Cr18Mn10Ni5Mo3N
Of urea with good corrosion resistance, can produce urea corrosion of the equipment.
1Cr17Mn6Ni5N
Nickel steel grade, instead of number 1 cr17ni7 and magnetism after cold working, used in railway vehicle, etc
1Cr18Mn8Ni5N
Nickel steel, instead of 1cr18ni9
0Cr25Ni20
Oxidation resistance is better than 0cr23ni13. Mostly used as heat resistant steel
A-29 1025
General use carbon steel rod
1025
These products have been used typically for use in fabrication of fittings, but usage is not limited to such applications. These products are not typically used for deep forming or cupping operations.
G10250
General use carbon steel rod
G2500
Used in the products of the automobile, truck, tractor, and allied industries; small cylinder blocks, cylinder heads, air cooled cylinders, pistons, clutch plates, oil pump bodies, transmission cases, gear boxes, clutch housings, and light-duty brake drum
F10005
Used in the products of the automobile, truck, tractor, and allied industries; small cylinder blocks, cylinder heads, air cooled cylinders, pistons, clutch plates, oil pump bodies, transmission cases, gear boxes, clutch housings, and light-duty brake drum
G2500a
Used in the products of the automobile, truck, tractor, and allied industries
G3500
Used in the products of the automobile, truck, tractor, and allied industries
G3500b
Diesel engine cylinder block, truck and tractor cylinder block and cylinder head, flywheel, tractor transmission case and heavy-load gear box
G3500c
Used in the products of the automobile, truck, tractor, and allied industries
W5
Carbon tool steel
T72305
Carbon tool steel
A5
Alloy tool steel
00Cr17Ni14Mo2
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
X2CrNiMo18-14-3
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
1.4435
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
Z 3 CND 17-11-02
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)

Relevant products

5ΧΗΜ Equivalent Grade Stock

Steel grade Dimension Shape Unit Quantity Delivery state Query
Cr12MoV 12-160(T)*310-610(W)*L Plate or Sheet Tons 12.38 Hot-Rolled+Annealed+black Enquiry
1.2601 12-160(T)*310-610(W)*L Plate or Sheet Tons 11.22 Hot-Rolled+Annealed+black Enquiry
A387 F5 & Grade 5 sheet Coil strip 0.5mmx200mmxC Coil or Strip Tons 3 Cold-Rolled+Annealed Enquiry
A387 F5 & Grade 5 Hot Coil stock Select Tons 3 Hot-Rolled+Annealed+black Enquiry
T45Cr5Si3 Round Bar Dia.40mm Round Bar Kgs 500 Hot-Rolled+Annealed+black Enquiry
1.2344(H13/X40CrMoV5-1/Z40CDV5) Stock List Dia.182mm - Dia.510mm Round Bar Tons 120 Forged+Annealed+black Enquiry
1.2714 Hot-Work Mould Steel Flat Bar Stock(2019-09-03) Select 0 Select Enquiry
15-5PH Forgrd Flat Bar Select 0 Select Enquiry
1.2714 Stock list 2020-06-15 Select 0 Select Enquiry
1.2714 QT Bar Stock List 2020-06-15 Select 0 Select Enquiry

Enquiry