400 Nickel Bar
400 Nickel Bar properties and heat treatment forged piece, Including 400 Nickel Bar application and specifications, We have all specifications，Including 400 Nickel Bar steel plate, 400 Nickel Bar sheet, 400 Nickel Bar square steel, 400 Nickel Bar flat bar,400 Nickel Bar round bar,400 Nickel Bar forgings, we can own production and sales.
Introduction to Our Products:
Specialized high quality steel
We have the advantages of equipment, technologies and price
forged/hot rolling/ extrusion of steel
We can produce the 400 Nickel Bar has the following specifications:
Round bar steel: 1mm to 3000mm
Square-shape steel: 1mm to 2000mm
Plate steel:0.1mm to 2500mm
Width: 10mm to 2500mm
Lenth: We can supply any lenth based on the customer's requirement.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Tubings: OD: φ6-219 mm, with wall thickness ranging from 1-35 mm.
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirementExcellent service for all kinds of industries,with advantages of technologies, equipment and price.
We serve you with our honesty, integrity, and professionality.
Chemical composition % of the ladle analysis of grade 400 Nickel Bar and Standards
400 Nickel Bar
UNS N04400
Nickel Alloy 400 and Monel® 400, also known as UNS N04400, is a ductile, nickel-copper based alloy comprised essentially of two-thirds nickel and one third copper. Nickel Alloy 400 is known for resistance to a variety of corrosive conditions, including alkalies (or acid like substances), saltwater, hydrofluoric acid and sulfuric acid. Other advantages of using this alloy are its toughness and high strength over a broad temperature range; it can also be manipulated to become magnetic if desired. Fortunately, if Nickel Alloy 400 doesn't meet your specific needs, NSA stocks other nickel-copper based alloys to choose from.
Industries that use 400 include:
- Chemical
- Marine
Products partially or completely constructed of 400 include:
- Electronic and electrical components
- Fresh water and gasoline tanks
- Heat exchangers
- Marine hardware and fixtures
- Process piping and vessels
- Propeller shafts
- Pumps
- Pump shafts
- Springs
- Valves
| As rolled stress relieved | Stocking Diameters | 1/2” to 8” |
|---|---|---|
| Material Lengths | Up to 12’ |
| Uns | Type | Ams | Astm | Federal | Characteristics |
|---|---|---|---|---|---|
| N04400 | ALLOY 400 | 4675 | B-164 | QQ-N-281 | Immense corrosion resistance and high strength over a wide range of temperatures. |
| C | MN | P | S | SI | CR | NI | MO | CU | OTHER | M/NM |
|---|---|---|---|---|---|---|---|---|---|---|
| .3 | 2. | .024 | .5 | Ni + Co = 63. - 70. | Balance | Fe 2.5 | INQUIRE |
Machining performance
Download 400 Nickel Bar the mechanical properties of the report, the report provides detailed performance analysis and application. Download >>
Principal Design Features
One of the most widely used precipitation hardening grades in the business. While soft and ductile in the solution annealed condition, it is capable of high properties with a single precipitation or aging treatment. Characterized by good corrosion resistance, high harness, toughness and strength.
Machinability
Long, gummy chips characterize this alloys machinability. It can be machined in the annealed condition, however condition H1150M will yield best results. Post machining solution treatment of parts will be required prior to final hardening if machining in this condition.
Heat Treatment
CONDITION A--Soak at 1900 F (1038 C) for 30 minutes and cool below 60 F (16 C) for complete martensite transformation. CONDITION H 950- Treat Condition A material at 900 F(482 C) for 1 hour, air cool.. CONDITION H925, H1025, H1075, H1100, H1150- Soak solution treated material for 4 hours at specified temperature, air cool, CONDITION H1150M- Soak solution treated material at 1400 F (760 C) for 2 hours, air cool, then re-heat to 1150 F (620 C) for 4 hours and air cool.
Welding
Successfully welded by common fusion and resistance methods, this alloy should not be joined by oxyacetylene welding. AWS E/ER630 filler metal is recommended if required.
Forging
Soak for 1 hour at 2150 F (1177 C) prior to forging. Do not work below 1850 F (1010 C). Post-work solution treatment is required prior to final hardening.